TECHNICAL SUPERIORITY OF Ultra Seal - XP

    ULTRA SEAL - XP IS NOT ONLY A BLEND OF SUCCESSFULLY TESTED ORGANIC FIBERS, BUT ALSO A BLEND OF THESE FIBERS IN CERTAIN CONCENTRATION WHICH ENHANCES THE SEALING CAPABILITY. THESE FIBERS ARE GROUND TO A PARTICULAR MICRON SIZED WI HCI I ARE BENEFICIAL IS SEALING OF THIEF ZONES. THERE ARE SOME ADDITIONAL COMPONENTS IN ULTRA SEAL - XP WHICH INHANCE ITS SUCCESSFUL PERFORMANCE SO WHEN CERTAIN CONDITION EXIST IN THE ENVIRONMENT IN WHICH THEY ARE BEING USED, ABOVE AVERAGE RESULTS COULD BE REALIZED.

ULTRA SEAL - XP
IS ORGANIC FIBERS
NON TOXIC AND BIO DEGRADABLE.
IT IS PARTICULARLY ATTRACTIVE FOR OFFSHORE USE IN THAT :
- IT HAS AN Lc 50 VALUE IN GENERIC MUD NO. 7 OF 1,000.000 PPM.
- IT REQUIRES NO ACIDIZING WHEN PLACED OVER PRODUCTION SANDS.
- NO SPECIAL EQUIPMENT IS NEEDED.
- IT REQUIRES NO ADDITIONAL CATALYST ADDITIVE.
- NO EXTRAORDINARY HANDLING OR MIXING PROCEDURES.
THE CRITERIA OF FIBER MATERIALS IN ULTRA SEAL- XP CAN BE BROKEN DOWN INTO TWO CATEGORIES.
1-SPECIFIC FIBER TYPE.
2- ACTUAL CONCENTRATION OF THE INDIVIDUAL FIBERS

SUBJECT . RECOMMENDED TREATMENT FOR ULTRA SEAL-AND ULTRA SEAL-C

- SEEPAGITLOSS
ADD ULTRA SEAL - XP TO THE DRILLING FLUID AT 2 TO 25 PPB AND SWEEP THE WELL BORE FOR MORE SEVERE LOSSES. FOLLOW SWEEP BY MIXING INTO THE SYSTEM AT CONCENTRATION OF 5 TO 8 PPB WITH SUFFICIENT ADDITION AS NEEDED FOR MAINTENANCE.
- TOTAL LOSS RETURNS :
MIX ULTRA SEAL- XP AT CONCENTRATION OF 25 TO 40 PPB COMBINED WITH 15 TO 40 PPB OF ULTRA SEAL - C IN EITHER THE SLUGGING TANK OR SUCTION PIT. IT CAN BE MIXED DIRECTLY THROUGH THE CHEMICAL HOPPER OR IN A RIBBION BLENDER.

- PERFORATING FLUID
MIX ULTRA SEAL - XP AT 15 TO 25 PPB CONCENTRATION IN THE DRILLING MUD OR BRINE SOLUTION . IF USING BRINE, ADD HEC, DRISPAC- REGULAR OR XCD TO INCREASE VISCOSITY OF THE BRINE TO +/-40 sec.qt BEFORE ADDING ULTRA SEAL-XP.
SPOT PILL ACROSS AREA TO BE PERFORATED THIS WILL HELP PREVENT FLUSHING OF THE PERFORATED ZONE.
- CORING FLUID
MIX ULTRA SEAL - XP AT 8 TO 10 PPB CONCENTRATION IN CORING FLUID . THIS WILL HELP PREVENT CORE FLUSHING BY THE FLUID AND MAKE RECOVERY AND INTERPRETATION EASIER.

- EXCESSIVE TORQUE OR DRAG :
MIX ULTRA SEAL - XP IN THE SLUGGING TANK AT CONCENTRATION OF 8 TO 12 PPB AND SWEEP THE WELL BORE. THIS SWEEP METHOD OF TREATMENT IS ALSO USEFULL JUST PRIOR TO LOGGING OR RUNNING CASING. IF TORQUE OR DRAG CONTINUES AS NEW HOLE IS DRILLED, REPEAT THE PROCEDURE.
ULTRA SEAL- XP CAN BE MDflED DM THE TOTAL MUD SYSTEM AT 5 TO 8 PPB WHILE DRILLING TO CONTINUALLY REPLACE ANY MATERIAL WHICH MAY BE REMOVED FROM THE WALLS OF THE WELL BORE BY THE STABILIZERS AND TOOL JOINTS WHILE DRILLING AND TRIPPING.

- CEMENT SPACER:
MIX ULTRA SEAL - XP S AT 25 PPB CONCENTRATION IN THE DRILLING MUD AND PUMP A HEAD OF THE CEMENT SLURRY. THIS APPLICATION IS USEFULL WHEN SETTING CEMENT PLUGS FOR DIRECTIONAL WORK ULTRA SEAL -XP CAN BE BLENDED TO 12 PPH IS CEMENT WITH VERY LITTLE EFFECT ON COMPRESSIVE STRENGTH.

    - Ultra Seal
                      + Ultra Seal - XP
                      + Ultra Seal - Poly Plug
                      + Ultra Seal - Plus
                      + Ultra Seal - c